Agenda: exercises-nagios-IV-VIII-medium.txt

% Nagios Installation and Configuration
%
# Introduction

## Goals

* Install and configure Nagios

## Notes

* Commands preceded with "$" imply that you should execute the command as
  a general user - not as root.
* Commands preceded with "#" imply that you should be working as root.
* Commands with more specific command lines (e.g. "rtrX>" or "mysql>") 
  imply that you are executing commands on remote equipment, or within 
  another program.

# Exercises

# PART IV - Adding Parent Relationships

Each item is a child of either a switch or a router in our classroom, EXCEPT for
your gateway router (rtrX) and the other members of your group. We are now going 
to add a "parents" statement for each device we have configured. 

If you are unsure of the parent relationships you can look at our classroom Network
Diagram. Remember, the parent relationships are from the point of view of your Nagios
instance running on your pc.

## 1. Adding Parents to switches.cfg

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ cd /etc/nagios3/conf.d
$ sudo editor switches.cfg
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Update the entry:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define host {
    use         generic-host
    host_name   sw
    alias       Backbone Switch
    address     10.10.0.253
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


to be


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define host {
    use         generic-host
    host_name   sw
    alias       Backbone Switch
    address     10.10.0.253
    parents     rtrX
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


Where "rtrX" is the gateway router for your group. I.E., for group 1 you 
would use "rtr1", for group 2, "rtr2" and so forth.

Save and exit from the file.


## 2. Adding Parents to routers.cfg

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo editor routers.cfg
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

For each entry we will add a "parents" line. So, for the gw definition at
the top of the file this should now look like:


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define host {
    use         generic-host
    host_name   gw
    alias       Classrooom Gateway Router
    address     10.10.0.254
    parents     sw
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

For all the remaining rtrX entries you should, also, add a line that says:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    parents     sw
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

EXCEPT For the rtrX entry for your group. There should be NO PARENTS entry. If you 
have an entry for "ap1" (classroom wireless access point), then the parents entry is,
also, "sw" - same as the other routers.

So, if you are in group 2, then the entries for groups 1, 2 and 3 would look like:


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define host {
    use         generic-host
    host_name   rtr1
    alias       Group 1 Router
    address     10.10.1.254
    parents     sw
}

define host {
    use         generic-host
    host_name   rtr2
    alias       Group 2 Router
    address     10.10.2.254
}

define host {
    use         generic-host
    host_name   rtr3
    alias       Group 3 Router
    address     10.10.3.254
    parents     sw
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


Update the rest of the file correctly and then save and exit from the file.


## 3. Adding Parents to pcs.cfg

For all the PC entries you should add a "parents" line that has the router 
for that PC's group. For the noc the parent is the core switch or "sw"

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#
# Classroom NOC
#

define host {
    use         generic-host
    host_name   noc
    alias       Workshop NOC machine
    address     10.10.0.250
    parents     sw
}


For PCs in Group 1 entries look like:


#
# Group 1
# 

define host {
    use         generic-host
    host_name   pc1
    alias       pc1
    address     10.10.1.1
    parents     rtr1
}

define host {
    use         generic-host
    host_name   pc2
    alias       pc2
    address     10.10.1.2
    parents     rtr1
}

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

etc



Do this for all the PCs in the remaining groups. I.E., pc5 in Group 2 has 
a parents statement of:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     parents    rtr2
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

BUT, FOR THE 4 ENTRIES FOR THE PCS IN YOUR GROUP DO NOT ADD ANY PARENTS STATEMENT!
REPEAT - THE PCS IN YOUR GROUP DO NOT HAVE ANY PARENT ENTRY!

Save and exit from the file.


## 4. Restart Nagios and See the Updated Status Map

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo service nagios3 restart
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

If you have errors, fix these and try restarting again.

Open a web browser to http://pcN.ws.nsrc.org/nagios3 and click on the "Map" link
on the left. Your map should now look quite different. You should see a map that
represents the Nagios world point of view from your machine.



# PART V - Create More Host Groups

## 0. Prep

In the web view, look at the pages "Hostgroup Overview", "Hostgroup
Summary", "Hostgroup Grid". This gives a convenient way to group together
hosts which are related (e.g. in the same site, serving the same purpose).

## 1. Update /etc/nagios3/conf.d/hostgroups_nagios2.cfg

For the following exercises it will be very useful if we have created
or update the following hostgroups:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      debian-servers
      routers
      switches
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
If you edit the file /etc/nagios3/conf.d/hostgroups_nagios2.cfg you
will see an entry for debian-servers that just contains localhost. 
Update this entry to include all the classroom PCs, including the
noc (this assumes that you created a "noc" entry in your pcs.cfg
file). Remember to skip your PC entry as it is represented by the
localhost entry.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo editor /etc/nagios3/conf.d/hostgroups_nagios2.cfg
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Update the entry that says:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
# A list of your Debian GNU/Linux servers
define hostgroup {
        hostgroup_name  debian-servers
                alias           Debian GNU/Linux Servers
                members         localhost
        }
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      
So that the "members" parameter contains something like this. Use your
classroom network diagram to confirm the exact number of machines and names
in your workshop.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  members    localhost,pc1,pc2,pc3,pc4,pc5,pc6,pc7,pc8,pc9,pc10,pc11,pc12, \
             pc13,pc14,pc15,pc16,pc17,pc18,pc19,pc20,pc21,pc22,pc23,pc24,pc25,\
             pc26,pc27,pc28,pc29,pc30,pc31,pc32,pc33,pc34,pc35,pc36
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Be sure that the end of the line has a "\" to indicate a new line. Otherwise
you will get an error when you go to restart Nagios. Remember that your own 
PC is "localhost", so skip your pc entry.

Once you have done this, add one more host group for our classroom switch(es).
If there is more than just one switch (sw.ws.nsrc.org) include this on the 
members line below, otherwise the entry at the end of the hostgroups_nagios2.cfg
file should look like (COPY and PASTE):

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~        
# A list of our switches
define hostgroup {
        hostgroup_name  switches
                alias           Classroom Switches
                members         sw
        }
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
            
When you are done be sure to verify your work and restart Nagios.
  
## 2. Go back to the web interface and look at your new Host Groups in Nagios.


# PART VI - Extended Host Information ("making your graphs pretty")

## 1. Update extinfo_nagios2.cfg 

If you would like to use appropriate icons for your defined hosts in
Nagios this is where you do this. We have the three types of devices:

* Cisco routers
* Cisco switches
* Ubuntu servers

There is a fairly large repository of icon images available for you to
use located here:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/share/nagios/htdocs/images/logos/
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

these were installed by default as dependent packages of the nagios3
package in Ubuntu. In some cases you can find model-specific icons for
your hardware, but to make things simpler we will use the following 
icons for our hardware:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/share/nagios/htodcs/images/logos/base/debian.*
/usr/share/nagios/htdocs/images/logos/cook/router.*
/usr/share/nagios/htdocs/images/logos/cook/switch.*
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

The next step is to edit the file /etc/nagios3/conf.d/extinfo_nagios2.cfg
and tell nagios what image you would like to use to represent your devices.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo editor /etc/nagios3/conf.d/extinfo_nagios2.cfg
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Here is what an entry for your routers looks like (there is already an entry
for debian-servers that will work as is). Note that the router model (3600) 
is not all that important. The image used represents a router in general.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define hostextinfo {
        hostgroup_name   routers 
        icon_image       cook/router.png
        icon_image_alt   Cisco Routers (7200)
        vrml_image       router.png 
        statusmap_image  cook/router.gd2
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note how we can simply use "hostgroup_name routers" as this has already been 
defined in the file hostgroups_nagios2.cfg. This makes configuring multiple, like
items much simpler.

Now add an entry for your switches. Once you are done check your work and 
restart Nagios. Take a look at the Status Map in the web interface (Map link
on the left). It should be much nicer, with real icons instead of question marks
for most items.


# PART VII - Create Service Groups

## 1. Create service groups for ssh and http for each set of pcs.

The idea here is to create three service groups. Each service group will
be for a quarter of the classroom. We want to see these PCs grouped together
and include status of their ssh and http services. To do this edit
and create the file:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ cd /etc/nagios3/conf.d                        (just to be sure)
$ sudo editor servicegroups.cfg
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Here is a sample of the service group for group 1:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
define servicegroup {
        servicegroup_name       group1-services
        alias                   group 1 services
        members  pc1,SSH,pc1,HTTP,pc2,SSH,pc2,HTTP,pc3,SSH,pc3,HTTP,pc4,SSH,pc4,HTTP
        }
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note that if the members line is too long you can use the "\" at the end to 
create a new line of members just below.
        
Note that "SSH" and "HTTP" need to be uppercase as this is how the service_description is
written in the file /etc/nagios3/conf.d/services_nagios2.cfg
          
You should create an entry for other groups of servers too.

CRITICAL - When you create an entry for your group remember to use "localhost" instead
of your "pcN" name since you have only defined your pc as localhost in the file 
hostgroups_nagios2.cfg.

Save your changes, verify your work and restart Nagios. Now if you click on the 
Service Groups menu item in the Nagios web interface you should see this information
grouped together. 
      

# PART VIII - Configure Guest Access to the Nagios Web Interface

## 1. You will edit the file /etc/nagios3/cgi.cfg to give read-only guest user access to the Nagios web interface.

By default Nagios is configured to give full r/w access via the Nagios
web interface to the user nagiosadmin. You can change the name of this
user, add other users, change how you authenticate users, what users
have access to what resources and more via the cgi.cfg file.

First, lets create a "guest" user and password in the htpasswd.users
file.
      
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo htpasswd /etc/nagios3/htpasswd.users guest
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

You can use any password you want (or none). A password of "guest" is 
not a bad choice.

Next, edit the file /etc/nagios3/cgi.cfg and look for what type of access
has been given to the nagiosadmin user. By default you will see the following 
directives (note, there are comments between each directive):

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
authorized_for_system_information=nagiosadmin
authorized_for_configuration_information=nagiosadmin
authorized_for_system_commands=nagiosadmin
authorized_for_all_services=nagiosadmin
authorized_for_all_hosts=nagiosadmin
authorized_for_all_service_commands=nagiosadmin
authorized_for_all_host_commands=nagiosadmin
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Now let's tell Nagios to allow the "guest" user some access to 
information via the web interface. You can choose whatever you would
like, but what is pretty typical is this:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
authorized_for_system_information=nagiosadmin,guest
authorized_for_configuration_information=nagiosadmin,guest
authorized_for_system_commands=nagiosadmin
authorized_for_all_services=nagiosadmin,guest
authorized_for_all_hosts=nagiosadmin,guest
authorized_for_all_service_commands=nagiosadmin
authorized_for_all_host_commands=nagiosadmin
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note we do not give the guest user access to system commands, service commands 
nor host commands.

Once you make the changes, save the file cgi.cfg, verify your 
work and restart Nagios. 

To see if you can log in as the "guest" user you will need to clear 
the cookies in your web browser or open an alternate web browser if you have one. 
You will not notice any difference in the web interface. The difference is that a 
number of items that are available via the web interface (forcing a service/host 
check, scheduling checks, comments, etc.) will not work for the guest user.

## 2. Enable External commands in nagios.cfg

This change is required in order to allow users to "Acknowledge" problems
with hosts and services in the Web interface.  The default file permissions
are set up in a secure way to prevent the web interface from updating
nagios, so you need to make them slightly more permissive.

First, edit the file "/etc/nagios3/nagios.cfg", and change the line:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        check_external_commands=0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

to

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        check_external_commands=1
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Save the file and exit.

Then, perform the following commands to change directory permissions and
to make the changes permanent:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
$ sudo /etc/init.d/nagios3 stop
$ sudo dpkg-statoverride --update --add nagios www-data 2710 /var/lib/nagios3/rw
$ sudo dpkg-statoverride --update --add nagios nagios 751 /var/lib/nagios3
$ sudo /etc/init.d/nagios3 start
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Once this is done, go to "Problems" > "Services (Unhandled)" and find a
service in the red (critical) or yellow (warning) state. Click on the
service name. Then under "Service commands" click on "Acknowledge this
service problem".

The problem should disappear from the list of unhandled problems.